The cart is empty
agd-r2r2-front
Audio-GD
agd-r2r2-frontr2r27r2r25r2r24dac19174_2018488044

Audio-GD - R2R 2 TCXO - Single Ended R2R FPGA Ladder DAC (DSD, DxD, Amanero USB)

€ 819
€ 677 excl VAT
Additional RCA output (Replacing ACSS)Information
Power cable (Default C13 EURO)
Audio-GD - Digital SPDIF coax interlink BNC (1m)Information
Audio-GD - Digital SPDIF coax interlink RCA (1m)Information
Audio-GD - Analogue RCA interlink stereo pair (1m)Information
Audio-GD - ACSS Analogue balanced interlink (mini-xlr)Information
Audio-GD - Optical Digital Toslink Cable (1M)Information
  • Description
  • Specifications

Audio-GD - R2R 2 - Discrete R2R DAC (DSD) TCXO

Single-ended digital analogue converter, equipped with multi discrete R-2R ladder per channel. All parts and components are selected based on excellent sonic and technical measurement performance. Components are e.g. from DALE resistors (USA), WIMA capacitors (Germany) and NOVER parts (UK). The used components but also the technical design (e.g. discrete analogue section and high speed FPGA's) of this system were being selected after many years of experience and practices and are considered to perform and provide supreme sonic results. Supporting today’s high resolutions including DSD and DxD and up to date interfaces like USB and LVDS I2S.


LATEST PRODUCT UPDATES

This product includes:

  • 20-10-2018: Latest v3 FPGA software updates
  • 28-03-2018: Latest R2R dac boards firmware release: Silent PCM sample rate switching
  • TCXO Upgrades


OPTIONS INCLUDED 
  • Dual R-2R discrete dac ladder per channel
  • Integrated 2 pairs of DA-8 R-2R modules
  • 2x ultra low-jitter TCXO clocks are included
  • Amanero Combo384 USB interface

SUMMARY
  • USB Amanero Combo384 interface
  • Programmable hardware design
  • Single ended output design
  • High speed FPGA's to control R-2R network
  • Lowest tolerance Vishay resistors applied in R-2R network
  • Discrete analogue output & power supply
  • Fully DC coupled design without capacitors in signal path
  • Non- feedback ACSS analog output control
  • Total of 5 regulated low noise class A power circuits

INPUTS
  • 1. RCA coaxial SPDIF
  • 2. USB 32-bit / 384kHz
  • 3. Optical toslink SPDIF
  • 4. HDMI IIS INPUT*

* Compatible with Mano Streamer (high res) and Pink Faun I2S stereo bridge


OUTPUTS
  • ACSS single ended (Optional RCA)
  • RCA single ended 

 R-2R DESIGN

The R-2R DAC has become popular and affordable. From DIY kits and completely up to of the shelf high-end products.
In the lower end DIY market, the R-2R design is often based on old technology; designed long time ago by MSB, often includes basic R2R ladder design only and not include the wonderful correction design of the modern MSB technology. Previous less good designs used data shift registers logic chips in serial mode to convert the data to an analog signal. The stubborn R2R issues cannot be avoided this way and performance is almost entirely depending on the accuracy of the ladder resistors. 

In the High-End of the shelf (finished products) market, the R2R design is usually much more complex when outstanding performance is offered. A basic R2R ladder is simply not sufficient to achieve the desired sound quality. Some manufacturers are using shift registers design to realize ladder compensation. A less complex, unfortunately also a less performing design based on traditional logic chips working in serial mode.
A far better design switches resistors in parallel mode; an ultra-fast FPGA chip controls and corrects the R2R ladder. The parallel design mode controls every bit respectively and therefore achieve unprecedented performance. (In parallel mode only 1 clock cycle is needed to output all data; serial design mode needs at minimum 8 up to 24 clock cycles) The parallel design is particularly complex, however when it is done properly it can correct every bit of the ladder. (Photo below shows a FPGA design with R2R ladder). With incredible speed and accuracy the R2R 7 will correct the unavoidable imperfections of the basic R2R ladder caused by tolerance of resistors; avoid glitches at ultra-high speed to deliver unrivaled musical performance.

TOLERANCE OF RESISTORS IN LADDER

Some manufactures claim to achieve good performance becuase they use lowest tolerance ladder resistors. The following calculation example will cover this. At 16 bit the tolerance of 1/66536, 0.1% (1/1000) it is by far not enough to achieve decent performance. Even using resistors with 0.01% (1/10000) tolerance, lowest tolerance available today,cannot deliver the desired performance This is just 16 bit, imagine a 24 calculation! To process 24 bit resolution it would require resistors with a tolerance of 0.00001%. This is purely theoretical; if this tolerance would exist the discreteness of the switch logic chips will already have too much internal impedance and will shake-up such design.The tolerance of the resistor will never solve Imperfections of a ladder.

The solution lies in the correction the ladder and not only depend on the tolerance of resistors. It’s a combination of both: Ultra-low tolerance resistors controlled by a correction technology using very high speed with parallel FPGA processing.


DIGITAL CONFIGURATION GUIDE
DSP configuration for R2R DAC's
 
 
Release Date July 2018
 
 
 
Firmware release: R7V2(X-X)
 
 
 
 
MODEL Jumper Setting Note
Oversampling Mode (OS) Bypass OFF Oversampling + digital passband filter
Non Oversampling mode (NOS) Bypass ON NON Oversampling + 6dB analogue filtering
       
Generic Settings
Jumper
Default
 Note
Input 4 clock regeneration
S0
OFF
Default is OFF. If the sound had issue, change the setting
Input 5 clock regeneration
S1
OFF
Default is OFF. If the sound had issue, change the setting
Input 6 clock regeneration
S2
OFF
Default is OFF. If the sound had issue, change the setting
PLL
PLLEN
OFF
 
Dithering
Dith
OFF
 
 
 
 
 
Oversampling (OS, digital passband filter)
Jumper
Jumper
BYPASS JUMPER OFF 
Oversampling
IPS0
IPS1
Default both OFF
8x
OFF
OFF
 
4x
ON
OFF
 
2x
OFF
ON
 
1x
ON
ON
 
 
 
 
 
NOS (Pure NOS, analogue 6dB Filter)
Jumper
Jumper
BYPASS JUMPER ON
NOS MODE
ATT0
ATT1
Default both OFF 
NOS 3
OFF
OFF
 
NOS 3
ON
OFF
 
NOS 2
OFF
ON
 
NOS 1
ON
ON
 
 
 
 
 

USB SUPPORT

Download USB Amanero drivers for Windows 10
Download USB Amanero drivers for Windows 7 & 8

No drivers required for Linux and/or Mac OS
OSX 10.6+ and Linux with UAC2 compliant kernel
Microsoft Windows: KS/Wasapi/WDM/ASIO


 

Brand URL : http://www.audio-gd.com/R2R/R2R2/R2R2EN.htm
Weight: 5.5 kg
Width: 240 mm
Length: 320 mm
Height: 80 mm
Brand: Audio-GDAudio-GD

Specifications

R-2R Discrete Ladder(s)
>108dB
2.5V (RCA) 2MA (ACSS)
0.5 Vp-p
19 dBm
USB / I2S 44.1kHz - 384kHz /32Bit | Coaxial: 44.1kHz - 192kHz /24Bit Optical: 44.1kHz - 192kHz /24Bit
1.0, 1.1, 2.0 & 3.0
Windows, iOS, Linux
5
15
W240 X L320 X H80 (Aluminium)
USB Cable
IEC Power Cord
audiophilles mh service

MUSIC LOVERS

PROFESSIONAL SERVICE

mh contact mh payable

PERSONAL ADVICE

AFFORDABLE

Facebook

icon dhl ship   icon ups ship   icon dpd ship   icon postnl ship   icon tnt ship

icon 64x64 ideal
keyboard_arrow_up
Cookies make it easier for us to provide you with our services. With the usage of our services you permit us to use cookies.
Ok